Sometimes, especially with older CD-ROM drives, the installer may fail to boot from a CD-ROM. The installer may also — even after booting successfully from CD-ROM — fail to recognize the CD-ROM or return errors while reading from it during the installation.
There are many different possible causes for these problems. We can only list some common issues and provide general suggestions on how to deal with them. The rest is up to you.
There are two very simple things that you should try first.
If the CD-ROM does not boot, check that it was inserted correctly and that it is not dirty.
If the installer fails to recognize a CD-ROM, try just running the optiona second time. Some DMA related issues with very old CD-ROM drives are known to be resolved in this way.
If this does not work, then try the suggestions in the subsections below. Most, but not all, suggestions discussed there are valid for both CD-ROM and DVD, but we'll use the term CD-ROM for simplicity.
If you cannot get the installation working from CD-ROM, try one of the other installation methods that are available.
Some older CD-ROM drives do not support reading from discs that were burned at high speeds using a modern CD writer.
Some very old CD-ROM drives do not work correctly if “direct memory access” (DMA) is enabled for them.
If the CD-ROM fails to boot, try the suggestions listed below.
Check that your BIOS actually supports booting from CD-ROM (only an issue for very old systems) and that CD booting is enabled in the BIOS.
If you downloaded an iso image, check that the md5sum of that image matches
the one listed for the image in the
MD5SUMS file that
should be present in the same location as where you downloaded the image
Next, check that the md5sum of the burned CD-ROM matches as well. The following command should work. It uses the size of the image to read the correct number of bytes from the CD-ROM.
$ dd if=/dev/cdrom | \ > head -c `stat --format=%s
debian-testing-i386-netinst.iso` | \ > md5sum a20391b12f7ff22ef705cee4059c6b92 - 262668+0 records in 262668+0 records out 134486016 bytes (134 MB) copied, 97.474 seconds, 1.4 MB/s
If, after the installer has been booted successfully, the CD-ROM is not detected, sometimes simply trying again may solve the problem. If you have more than one CD-ROM drive, try changing the CD-ROM to the other drive. If that does not work or if the CD-ROM is recognized but there are errors when reading from it, try the suggestions listed below. Some basic knowledge of kFreeBSD is required for this. To execute any of the commands, you should first switch to the second virtual console (VT2) and activate the shell there.
Switch to VT4 or view the contents of
(use nano as editor) to check for any specific error
messages. After that, also check the output of dmesg.
Check in the output of dmesg if your CD-ROM drive was recognized. You should see something like (the lines do not necessarily have to be consecutive):
Probing IDE interface ide1... hdc: TOSHIBA DVD-ROM SD-R6112, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hdc: ATAPI 24X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20
If you don't see something like that, chances are the controller your CD-ROM is connected to was not recognized or may be not supported at all. If you know what driver is needed for the controller, you can try loading it manually using modprobe.
Check that there is a device node for your CD-ROM drive under
/dev/. In the example above, this would be
There should also be a
Use the mount command to check if the CD-ROM is already mounted; if not, try mounting it manually:
$ mount /dev/
Check if there are any error messages after that command.
Check if DMA is currently enabled:
$ cd /proc/
hdc$ grep using_dma settings using_dma 1 0 1 rw
A “1” in the first column after
means it is enabled. If it is, try disabling it:
$ echo -n "using_dma:0" >settings
Make sure that you are in the directory for the device that corresponds to your CD-ROM drive.
If there are any problems during the installation, try checking the integrity of the CD-ROM using the option near the bottom of the installer's main menu. This option can also be used as a general test if the CD-ROM can be read reliably.
If you have problems and the kernel hangs during the boot process, doesn't recognize peripherals you actually have, or drives are not recognized properly, the first thing to check is the boot parameters, as discussed in Section 5.3, “Boot Parameters”.
During the boot sequence, you may see many messages in the form
can't find ,
this driver release depends
Most of these messages are harmless. You
see them because the kernel for the installation system is built to
run on computers with many different peripheral devices. Obviously, no
one computer will have every possible peripheral device, so the
operating system may emit a few complaints while it looks for
peripherals you don't own. You may also see the system pause for a
while. This happens when it is waiting for a device to respond, and
that device is not present on your system. If you find the time it
takes to boot the system unacceptably long, you can create a
custom kernel later .
If you get through the initial boot phase but cannot complete the install, the menu optionmay be helpful. It lets you store system error logs and configuration information from the installer to a floppy, or download them using a web browser. This information may provide clues as to what went wrong and how to fix it. If you are submitting a bug report, you may want to attach this information to the bug report.
Other pertinent installation messages may be found in
/var/log/ during the
after the computer has been booted into the installed system.
If you still have problems, please submit an installation report. We also encourage installation reports to be sent even if the installation is successful, so that we can get as much information as possible on the largest number of hardware configurations.
Note that your installation report will be published in the Debian Bug Tracking System (BTS) and forwarded to a public mailing list. Make sure that you use an e-mail address that you do not mind being made public.
If you have a working Debian system, the easiest way to send an installation
report is to install the
(aptitude install installation-report reportbug),
reportbug as explained in
Section 8.5.2, “Sending E-Mails Outside The System”, and run the command reportbug
Alternatively you can use this template when filling out
installation reports, and file the report as a bug report against the
installation-reports pseudo package, by sending it to
Package: installation-reports Boot method: <How did you boot the installer? CD? floppy? network?> Image version: <Full URL to image you downloaded is best> Date: <Date and time of the install> Machine: <Description of machine (eg, IBM Thinkpad R32)> Processor: Memory: Partitions: <df -Tl will do; the raw partition table is preferred> Output of lspci -knn (or lspci -nn): Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [ ] Detect network card: [ ] Configure network: [ ] Detect CD: [ ] Load installer modules: [ ] Detect hard drives: [ ] Partition hard drives: [ ] Install base system: [ ] Clock/timezone setup: [ ] User/password setup: [ ] Install tasks: [ ] Install boot loader: [ ] Overall install: [ ] Comments/Problems: <Description of the install, in prose, and any thoughts, comments and ideas you had during the initial install.>
In the bug report, describe what the problem is, including the last visible kernel messages in the event of a kernel hang. Describe the steps that you did which brought the system into the problem state.