Debian does not impose hardware requirements beyond the requirements of the Linux or kFreeBSD kernel and the GNU tool-sets. Therefore, any architecture or platform to which the Linux or kFreeBSD kernel, libc, gcc, etc. have been ported, and for which a Debian port exists, can run Debian. Please refer to the Ports pages at https://www.debian.org/ports/amd64/ for more details on 64-bit PC architecture systems which have been tested with Debian GNU/Linux.
Rather than attempting to describe all the different hardware configurations which are supported for 64-bit PC , this section contains general information and pointers to where additional information can be found.
Debian GNU/Linux 10 supports ten major architectures and several variations of each architecture known as “flavors”.
|Intel x86-based||i386||default x86 machines||default|
|Xen PV domains only||xen|
|AMD64 & Intel 64||amd64|
|ARM||armel||Marvell Kirkwood and Orion||marvell|
|ARM with hardware FPU||armhf||multiplatform||armmp|
|32bit MIPS (big-endian)||mips||MIPS Malta||4kc-malta|
|64bit MIPS (little-endian)||mips64el||MIPS Malta||5kc-malta|
|32bit MIPS (little-endian)||mipsel||MIPS Malta||4kc-malta|
|Power Systems||ppc64el||IBM POWER8 or newer machines|
|64bit IBM S/390||s390x||IPL from VM-reader and DASD||generic|
This document covers installation for the 64-bit PC architecture using the Linux kernel. If you are looking for information on any of the other Debian-supported architectures take a look at the Debian-Ports pages.
From a technical point of view, laptops are normal PCs, so all information regarding PC systems applies to laptops as well. Installations on laptops nowadays usually work out of the box, including things like automatically suspending the system on closing the lid and laptop specfic hardware buttons like those for disabling the wifi interfaces (“airplane mode”). Nonetheless sometimes the hardware vendors use specialized or proprietary hardware for some laptop-specific functions which might not be supported. To see if your particular laptop works well with GNU/Linux, see for example the Linux Laptop pages.
Multiprocessor support — also called “symmetric multiprocessing” or SMP — is available for this architecture. The standard Debian 10 kernel image has been compiled with SMP-alternatives support. This means that the kernel will detect the number of processors (or processor cores) and will automatically deactivate SMP on uniprocessor systems.
Having multiple processors in a computer was originally only an issue for high-end server systems but has become common in recent years nearly everywhere with the introduction of so called “multi-core” processors. These contain two or more processor units, called “cores”, in one physical chip.
Debian's support for graphical interfaces is determined by the underlying support found in X.Org's X11 system, and the kernel. Basic framebuffer graphics is provided by the kernel, whilst desktop environments use X11. Whether advanced graphics card features such as 3D-hardware acceleration or hardware-accelerated video are available, depends on the actual graphics hardware used in the system and in some cases on the installation of additional “firmware” images (see Section 2.2, “Devices Requiring Firmware”).
On modern PCs, having a graphical display usually works out of the box. In very few cases there have been reports about hardware on which installation of additional graphics card firmware was required even for basic graphics support, but these have been rare exceptions. For quite a lot of hardware, 3D acceleration also works well out of the box, but there is still some hardware that needs binary blobs to work well.
Details on supported graphics hardware and pointing devices can be found at https://wiki.freedesktop.org/xorg/. Debian 10 ships with X.Org version 7.7.
Almost any network interface card (NIC) supported by the Linux kernel should also be supported by the installation system; drivers should normally be loaded automatically. This includes most PCI/PCI-Express cards as well as PCMCIA/Express Cards on laptops.
ISDN is supported, but not during the installation.
Wireless networking is in general supported as well and a growing number of wireless adapters are supported by the official Linux kernel, although many of them do require firmware to be loaded.
If firmware is needed, the installer will prompt you to load firmware. See Section 6.4, “Loading Missing Firmware” for detailed information on how to load firmware during the installation.
Wireless NICs that are not supported by the official Linux kernel can generally be made to work under Debian GNU/Linux, but are not supported during the installation.
If there is a problem with wireless and there is no other NIC you can use during the installation, it is still possible to install Debian GNU/Linux using a full CD-ROM or DVD image. Select the option to not configure a network and install using only the packages available from the CD/DVD. You can then install the driver and firmware you need after the installation is completed (after the reboot) and configure your network manually.
In some cases the driver you need may not be available as a Debian package.
You will then have to look if there is source code available in the internet
and compile the driver yourself. How to do this is outside the scope of this
If no Linux driver is available, your last resort is to
ndiswrapper package, which allows you to use
a Windows driver.
Support for braille displays is determined by the underlying support
brltty. Most displays work under
brltty, connected via either a serial port, USB
or bluetooth. Details on supported braille devices can be found on the
Debian GNU/Linux 10 ships with
Support for hardware speech synthesis devices is determined by the
underlying support found in
speakup only supports integrated boards and
external devices connected to a serial port (no USB, serial-to-USB or PCI
adapters are supported). Details on supported hardware speech synthesis
devices can be found on the
Debian GNU/Linux 10 ships with
Linux supports a large variety of hardware devices such as mice, printers, scanners, PCMCIA/CardBus/ExpressCard and USB devices. However, most of these devices are not required while installing the system.
USB hardware generally works fine. On some very old PC systems some USB keyboards may require additional configuration (see Section 3.6.5, “Hardware Issues to Watch Out For”). On modern PCs, USB keyboards and mice work without requiring any specific configuration.