The Debian Installer consists of a number of special-purpose components to perform each installation task. Each component performs its task, asking the user questions as necessary to do its job. The questions themselves are given priorities, and the priority of questions to be asked is set when the installer is started.
When a default installation is performed, only essential (high priority) questions will be asked. This results in a highly automated installation process with little user interaction. Components are automatically run in sequence; which components are run depends mainly on the installation method you use and on your hardware. The installer will use default values for questions that are not asked.
If there is a problem, the user will see an error screen, and the installer menu may be shown in order to select some alternative action. If there are no problems, the user will never see the installer menu, but will simply answer questions for each component in turn. Serious error notifications are set to priority “critical” so the user will always be notified.
Some of the defaults that the installer uses can be influenced by passing
boot arguments when
debian-installer is started. If, for example, you wish to
force static network configuration (IPv6 autoconfiguration and DHCP are
used by default if available),
you could add the boot parameter
See Section 5.2.1, “Debian Installer Parameters” for available options.
Power users may be more comfortable with a menu-driven interface,
where each step is controlled by the user rather than the installer
performing each step automatically in sequence. To use the installer
in a manual, menu-driven way, add the boot argument
If your hardware requires you to pass options to kernel modules as
they are installed, you will need to start the installer in
“expert” mode. This can be done by either using the
expert command to start the installer or by adding
the boot argument
Expert mode gives you full control over
For this architecture the installer uses a character-based user interface. A graphical user interface is currently not available.
In the character-based environment the use of a mouse is not supported. Here are the keys you can use to navigate within the various dialogs. The Tab or right arrow keys move “forward”, and the Shift+Tab or left arrow keys move “backward” between displayed buttons and selections. The up and down arrow select different items within a scrollable list, and also scroll the list itself. In addition, in long lists, you can type a letter to cause the list to scroll directly to the section with items starting with the letter you typed and use Pg-Up and Pg-Down to scroll the list in sections. The space bar selects an item such as a checkbox. Use Enter to activate choices.
Some dialogs may offer additional help information. If help is available this will be indicated on the bottom line of the screen by displaying that help information can be accessed by pressing the F1 key.
S/390 does not support virtual consoles. You may open a second and third ssh session to view the logs described below.
Error messages and logs are redirected to the fourth console. You can access this console by pressing Left Alt+F4 (hold the left Alt key while pressing the F4 function key); get back to the main installer process with Left Alt+F1.
These messages can also be found in
/var/log/syslog. After installation, this log
is copied to
/var/log/installer/syslog on your
new system. Other installation messages may be found in
/var/log/ during the
after the computer has been booted into the installed system.
The graphical installer basically works the same as the text-based installer and thus the rest of this manual can be used to guide you through the installation process.
If you prefer using the keyboard over the mouse, there are two things you need to know. To expand a collapsed list (used for example for the selection of countries within continents), you can use the + and - keys. For questions where more than one item can be selected (e.g. task selection), you first need to tab to the button after making your selections; hitting enter will toggle a selection, not activate .
If a dialog offers additional help information, a F1 key.button will be displayed. The help information can be accessed either by activating the button or by pressing the
To switch to another console, you will also need to use the Ctrl key, just as with the X Window System. For example, to switch to VT2 (the first debug shell) you would use: Ctrl+Left Alt+F2. The graphical installer itself runs on VT5, so you can use Left Alt+F5 to switch back.