Bug#402416: linux-image-2.6.18-3-686: 2.6.18-3 fails to boot (failure during root fs mount)
Package: linux-image-2.6.18-3-686
Version: 2.6.18-7
Severity: critical
Justification: breaks the whole system
I upgraded linux-image to linux-image-2.6.18-3-686 and it fails to boot.
My system uses md RAID1 for / (/dev/md1) with standard initramfs config
files.
Following is the boot information captured through a serial console as
well as a correct boot sequence for the current linux-image-2.6.17-2-686
kernel.
#-----------------------------------------------------------------------
# 2.6.18-7 boot
#-----------------------------------------------------------------------
Linux version 2.6.18-3-686 (Debian 2.6.18-7) (waldi@debian.org) (gcc
version 4.1.2 20061115 (prerelease) (Debian 4.1.1-20)) #1 SMP Mon Dec 4
16:41:14 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005ff30000 (usable)
BIOS-e820: 000000005ff30000 - 000000005ff40000 (ACPI data)
BIOS-e820: 000000005ff40000 - 000000005fff0000 (ACPI NVS)
BIOS-e820: 000000005fff0000 - 0000000060000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
639MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000ff780
DMI 2.3 present.
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 70000000 (gap: 60000000:9fb80000)
Detected 2598.859 MHz processor.
Built 1 zonelists. Total pages: 393008
Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,19200
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1550420k/1572032k available (1543k kernel code, 20392k reserved,
574k data, 196k init, 654528k highmem)
Checking if this processor honours the WP bit even in supervisor mode...
Ok.
Calibrating delay using timer specific routine.. 5201.60 BogoMIPS
(lpj=10403218)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5197.89 BogoMIPS
(lpj=10395781)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
Total of 2 processors activated (10399.49 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=24
checking if image is initramfs... it is
Freeing initrd memory: 4584k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
ASUS P4P800 detected. Disabling PnPBIOS
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a
report
pnp: 00:09: ioport range 0x680-0x6ff has been reserved
pnp: 00:09: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: efd00000-f1dfffff
PREFETCH window: dfc00000-efbfffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: f1e00000-f7efffff
PREFETCH window: 70000000-700fffff
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1165744816.856:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports<6>Time: tsc clocksource has been installed.
S0 S1 S3 S4 S5)
Freeing unused kernel memory: 196k freed
Loading, please wait...
Begin: Loading essential drivers... ...
Done.
Begin: Running /scripts/init-premount ...
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 169, io base 0x0000eec0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 177
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 177, io base 0x0000ef00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 185, io base 0x0000ef20
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 169
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 169, io base 0x0000ef40
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1: new full speed USB device using uhci_hcd and address 2
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
usb 2-1: configuration #1 chosen from 1 choice
hdc: TOSHIBA ODD-DVD SD-M1802, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide1 at 0x170-0x177,0x376 on irq 15
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 185
ata1: SATA max UDMA/133 cmd 0xEFF0 ctl 0xEFE6 bmdma 0xEF90 irq 185
ata2: SATA max UDMA/133 cmd 0xEFA8 ctl 0xEFE2 bmdma 0xEF98 irq 185
scsi0 : ata_piix
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ata1.00: ATA-7, max UDMA7, 312581808 sectors: LBA48
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/133
scsi1 : ata_piix
ata2.00: ATA-7, max UDMA7, 312581808 sectors: LBA48
ata2.00: ata2: dev 0 multi count 16
ata2.00: configured for UDMA/133
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 193
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: irq 193, io mem 0xf7fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
usb 2-1: USB disconnect, address 2
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt 0000:02:05.0[A] -> <5>SCSI device sdb: 312581808
512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 sdb4
GSI 22 (level, low) -> IRQ 201
sd 1:0:0:0: Attached scsi disk sdb
skge 1.6 addr 0xf7efc000 irq 201 chip Yukon-Lite rev 7
skge eth0: addr 00:0e:a6:89:f0:3b
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:0c.0: 3Com PCI 3c905 Boomerang 100baseTx at 0001df00.
Done.
Begin: Mounting root file system... ...
Begin: Running /scripts/local-top ...
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
md: raid1 personality registered for level 1
mdadm: error opening /dev/md1: No such file or directory
mknod: sda: File exists
mknod: sda1: File exists
mknod: sda2: File exists
mknod: sda3: File exists
mknod: sda4: File exists
mknod: sdb: File exists
mknod: sdb1: File exists
mknod: sdb2: File exists
mknod: sdb3: File existsmd: md0 stopped.
mknod: sdb4: Fmd: bind<sda3>
ile exists
md: bind<sdb3>
raid1: raid set md0 active with 2 out of 2 mirrors
mdadm: /dev/md0 has been started with 2 drives.
md: md1 stopped.
md: bind<sda4>
md: bind<sdb4>
raid1: raid set md1 active with 2 out of 2 mirrors
mdadm: /dev/md1 has been started with 2 drives.
Done.
Begin: Running /scripts/local-premount ...
Done.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Begin: Running /scripts/local-bottom ...
Done.
Done.
Begin: Running /scripts/init-bottom ...
mount: Mounting /root/dev on /dev/.static/dev failed: No such file or
directory
Done.
mount: Mounting /sys on /root/sys failed: No such file or directory
mount: Mounting /proc on /root/proc failed: No such file or directory
Target filesystem doesn't have /sbin/init
BusyBox v1.1.3 (Debian 1:1.1.3-3) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/bin/sh: can't access tty; job control turned off
(initramfs)
#-----------------------------------------------------------------------
# 2.6.18-7 boot
#-----------------------------------------------------------------------
Linux version 2.6.17-2-686 (Debian 2.6.17-9) (waldi@debian.org) (gcc version 4.1.2 20060901 (prerelease) (Debian 4.1.1-13)) #1 SMP Wed Sep 13 16:34:10 UTC 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005ff30000 (usable)
BIOS-e820: 000000005ff30000 - 000000005ff40000 (ACPI data)
BIOS-e820: 000000005ff40000 - 000000005fff0000 (ACPI NVS)
BIOS-e820: 000000005fff0000 - 0000000060000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
383MB HIGHMEM available.
1152MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 393008
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 290816 pages, LIFO batch:31
HighMem zone: 98096 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000fad60
ACPI: RSDT (v001 A M I OEMRSDT 0x01000427 MSFT 0x00000097) @ 0x5ff30000
ACPI: FADT (v002 A M I OEMFACP 0x01000427 MSFT 0x00000097) @ 0x5ff30200
ACPI: MADT (v001 A M I OEMAPIC 0x01000427 MSFT 0x00000097) @ 0x5ff30390
ACPI: OEMB (v001 A M I OEMBIOS 0x01000427 MSFT 0x00000097) @ 0x5ff40040
ACPI: DSDT (v001 A0049 A0049000 0x00000000 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 70000000 (gap: 60000000:9fb80000)
Built 1 zonelists
Kernel command line: root=/dev/md1 ro console=tty0 console=ttyS0,19200
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Detected 2599.070 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 131072 (order: 7, 524288 bytes)
Memory: 1553080k/1572032k available (1482k kernel code, 17820k reserved, 544k data, 196k init, 392384k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 5203.15 BogoMIPS (lpj=10406310)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5197.86 BogoMIPS (lpj=10395726)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
Total of 2 processors activated (10401.01 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=4000
checking if image is initramfs... it is
Freeing initrd memory: 1335k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
ASUS P4P800 detected. Disabling PnPBIOS
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:09: ioport range 0x680-0x6ff has been reserved
pnp: 00:09: ioport range 0x290-0x297 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: efd00000-f1dfffff
PREFETCH window: dfc00000-efbfffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-dfff
MEM window: f1e00000-f7efffff
PREFETCH window: 70000000-700fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1165744957.820:1): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI wakeup devices:
P0P4 MC97 USB1 USB2 USB3 USB4 EUSB ILAN
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 196k freed
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
hw_random: RNG not detected
Linux video capture interface: v1.00
cx2388x v4l2 driver version 0.0.5 loaded
ACPI: PCI Interrupt 0000:02:0a.0[A] -> GSI 22 (level, low) -> IRQ 169
CORE cx88[0]: subsystem: 0070:9002, board: Hauppauge Nova-T DVB-T [card=18,autodetected]
TV tuner 4 at 0x1fe, Radio tuner -1 at 0x1fe
tveeprom 0-0050: Hauppauge model 90002, rev C176, serial# 85140
tveeprom 0-0050: MAC address is 00-0D-FE-01-4C-94
tveeprom 0-0050: tuner model is Thompson DTT7592 (idx 76, type 4)
tveeprom 0-0050: TV standards ATSC/DVB Digital (eeprom 0x80)
tveeprom 0-0050: audio processor is None (idx 0)
tveeprom 0-0050: decoder processor is CX882 (idx 25)
tveeprom 0-0050: has no radio, has IR remote
cx88[0]: hauppauge eeprom: model=90002
input: cx88 IR (Hauppauge Nova-T DVB-T as /class/input/input0
cx88[0]/0: found at 0000:02:0a.0, rev: 5, irq: 169, latency: 64, mmio: 0xf4000000
cx88[0]/0: registered device video0 [v4l2]
cx88[0]/0: registered device vbi0
mice: PS/2 mouse device common for all mice
SCSI subsystem initialized
libata version 1.20 loaded.
ata_piix 0000:00:1f.2: version 1.05
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xEFF0 ctl 0xEFE6 bmdma 0xEF90 irq 177
ata2: SATA max UDMA/133 cmd 0xEFA8 ctl 0xEFE2 bmdma 0xEF98 irq 177
ata1: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3c69 86:3c01 87:4003 88:20ff
ata1: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ata2: dev 0 cfg 49:2f00 82:346b 83:7f01 84:4003 85:3c69 86:3c01 87:4003 88:20ff
ata2: dev 0 ATA-7, max UDMA7, 312581808 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: SAMSUNG SP1614C Rev: SW10
Type: Direct-Access ANSI SCSI revision: 05
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 312581808 512-byte hdwr sectors (160042 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 312581808 512-byte hdwr sectors (160042 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 sdb4
sd 1:0:0:0: Attached scsi disk sdb
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
md: raid1 personality registered for level 1
md: md1 stopped.
md: bind<sda3>
md: bind<sdb3>
raid1: raid set md1 active with 2 out of 2 mirrors
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 865 Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 185, io base 0x0000eec0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hw_random: RNG not detected
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 193, io base 0x0000ef00
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP]
CAPI Subsystem Rev 1.1.2.8
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 177, io base 0x0000ef20
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
ACPI: PCI Interrupt 0000:00:1d.3[A] -> <4>fcpci: module license 'Proprietary' taints kernel.
GSI 16 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 185, io base 0x0000ef40
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
fcpci: AVM FRITZ!Card PCI driver, revision 0.7.2
fcpci: (fcpci built on Oct 18 2006 at 13:44:08)
fcpci: -- 32 bit CAPI driver --
usb 2-1: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 201, io mem 0xf7fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 169
skge 1.5 addr 0xf7efc000 irq 169 chip Yukon-Lite rev 7
skge eth0: addr 00:0e:a6:89:f0:3b
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:0c.0: 3Com PCI 3c905 Boomerang 100baseTx at 0001df00.
ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 217
fcpci: AVM FRITZ!Card PCI found: port 0xdf80, irq 217
fcpci: Loading...
fcpci: Driver 'fcpci' attached to fcpci-stack. (152)
fcpci: Stack version 3.11-07
kcapi: Controller 1: fcpci-df80-217 attached
kcapi: card 1 "fcpci-df80-217" ready.
fcpci: Loaded.
ICH5: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
cx2388x dvb driver version 0.0.5 loaded
usb 2-1: new full speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
Bluetooth: Core ver 2.8
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Probing IDE interface ide1...
hci_usb: Unknown symbol hci_free_dev
hci_usb: Unknown symbol hci_alloc_dev
hci_usb: Unknown symbol hci_unregister_dev
hci_usb: Unknown symbol hci_register_dev
hci_usb: Unknown symbol hci_free_dev
hci_usb: Unknown symbol hci_alloc_dev
hci_usb: Unknown symbol hci_unregister_dev
hci_usb: Unknown symbol hci_register_dev
Bluetooth: HCI USB driver ver 2.9
usbcore: registered new driver hci_usb
hdc: TOSHIBA ODD-DVD SD-M1802, ATAPI CD/DVD-ROM drive
hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1f.5 to 64
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
AC'97 0 analog subsections not ready
hdd: No disk in drive
intel8x0_measure_ac97_clock: measured 52186 usecs
hdd: 98304kB, 96/64/32 CHS, 4096 kBps, 512 sector size, 2941 rpm
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:02:0a.2[A] -> GSI 22 (level, low) -> IRQ 169
cx88[0]/2: found at 0000:02:0a.2, rev: 5, irq: 169, latency: 64, mmio: 0xf5000000
cx88[0]/2: cx2388x based dvb card
DVB: registering new adapter (cx88[0]).
DVB: registering frontend 0 (Conexant CX22702 DVB-T)...
cx2388x blackbird driver version 0.0.5 loaded
Adding 498004k swap on /dev/sda2. Priority:-1 extents:1 across:498004k
Adding 498004k swap on /dev/sdb2. Priority:-2 extents:1 across:498004k
EXT3-fs warning: maximal mount count reached, running e2fsck is recommended
EXT3 FS on md1, internal journal
usbcore: registered new driver ov511
drivers/media/video/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
capifs: Rev 1.1.2.3
capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
md: md0 stopped.
md: bind<sda4>
md: bind<sdb4>
raid1: raid set md0 active with 2 out of 2 mirrors
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
skge eth0: enabling interface
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
eth1: setting full-duplex.
Netfilter messages via NETLINK v0.30.
ip_conntrack version 2.4 (8192 buckets, 65536 max) - 224 bytes per conntrack
ctnetlink v0.90: registering with nfnetlink.
ip_conntrack_pptp version 3.1 loaded
ip_nat_pptp version 3.0 loaded
ip_tables: (C) 2000-2006 Netfilter Core Team
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
IPv6 over IPv4 tunneling driver
ip6_tables: (C) 2000-2006 Netfilter Core Team
skge eth0: Link is up at 1000 Mbps, full duplex, flow control tx and rx
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
#-----------------------------------------------------------------------
# End boot
#-----------------------------------------------------------------------
-- System Information:
Debian Release: 3.1
APT prefers stable
APT policy: (990, 'stable'), (300, 'testing')
Architecture: i386 (i686)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.17-2-686
Locale: LANG=en_US, LC_CTYPE=en_US (charmap=ISO-8859-1)
Versions of packages linux-image-2.6.18-3-686 depends on:
ii coreutils 5.97-5 The GNU core utilities
ii debconf [debconf-2.0] 1.4.30.13 Debian configuration management sy
ii initramfs-tools [linux-initra 0.85b tools for generating an initramfs
ii module-init-tools 3.3-pre3-1 tools for managing Linux kernel mo
ii yaird [linux-initramfs-tool] 0.0.12-18 Yet Another mkInitRD
Versions of packages linux-image-2.6.18-3-686 recommends:
pn libc6-i686 <none> (no description available)
-- debconf information:
linux-image-2.6.18-3-686/postinst/bootloader-error-2.6.18-3-686:
linux-image-2.6.18-3-686/postinst/old-dir-initrd-link-2.6.18-3-686: true
linux-image-2.6.18-3-686/postinst/kimage-is-a-directory:
linux-image-2.6.18-3-686/postinst/old-system-map-link-2.6.18-3-686: true
linux-image-2.6.18-3-686/postinst/create-kimage-link-2.6.18-3-686: true
linux-image-2.6.18-3-686/postinst/bootloader-test-error-2.6.18-3-686:
linux-image-2.6.18-3-686/preinst/abort-overwrite-2.6.18-3-686:
linux-image-2.6.18-3-686/postinst/old-initrd-link-2.6.18-3-686: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.18-3-686/preinst/elilo-initrd-2.6.18-3-686: true
linux-image-2.6.18-3-686/preinst/lilo-initrd-2.6.18-3-686: true
linux-image-2.6.18-3-686/postinst/depmod-error-initrd-2.6.18-3-686: false
linux-image-2.6.18-3-686/preinst/bootloader-initrd-2.6.18-3-686: true
linux-image-2.6.18-3-686/prerm/removing-running-kernel-2.6.18-3-686: true
linux-image-2.6.18-3-686/prerm/would-invalidate-boot-loader-2.6.18-3-686: true
linux-image-2.6.18-3-686/preinst/abort-install-2.6.18-3-686:
linux-image-2.6.18-3-686/preinst/overwriting-modules-2.6.18-3-686: true
linux-image-2.6.18-3-686/preinst/initrd-2.6.18-3-686:
linux-image-2.6.18-3-686/preinst/lilo-has-ramdisk:
linux-image-2.6.18-3-686/preinst/already-running-this-2.6.18-3-686:
linux-image-2.6.18-3-686/postinst/depmod-error-2.6.18-3-686: false
linux-image-2.6.18-3-686/preinst/failed-to-move-modules-2.6.18-3-686:
Reply to: