Bug#386226: linux-image-2.6.22-2-686: Still here in 2.6.22-2
Package: linux-image-2.6.22-2-686
Version: 2.6.22-4
Followup-For: Bug #386226
I am still experiencing this bug on Dell Vostro 1500. The --directisa
fix does
not work, but blacklisting the rtc kernel module does allow hwclock to
start without
problems.
-- Package-specific info:
** Version:
Linux version 2.6.22-2-686 (Debian 2.6.22-4) (waldi@debian.org) (gcc
version 4.1.3 20070812 (prerelease) (Debian 4.1.2-15)) #1 SMP Fri Aug 31
00:24:01 UTC 2007
** Not tainted
** Kernel log:
usb 4-2.2: configuration #1 chosen from 1 choice
usb 4-2.3: new full speed USB device using uhci_hcd and address 5
usb 4-2.3: rejected 1 configuration due to insufficient available bus
power
usb 4-2.3: no configuration chosen from 1 choice
usb 4-2.4: new low speed USB device using uhci_hcd and address 6
usb 4-2.4: configuration #1 chosen from 1 choice
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected an Intel 965GM Chipset.
agpgart: Detected 7676K stolen memory.
agpgart: AGP aperture is 256M @ 0xe0000000
input: PC Speaker as /class/input/input1
usbcore: registered new interface driver hiddev
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
Real Time Clock Driver v1.12ac
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 4 if 1
alt 0 proto 2 vid 0x03F0 pid 0x2F11
input: HID 1241:1203 as /class/input/input2
input: USB HID v1.11 Keyboard [HID 1241:1203] on usb-0000:00:1d.1-2.2
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:03:01.1 [1180:0822] (rev 22)
ACPI: PCI Interrupt 0000:03:01.1[B] -> GSI 18 (level, low) -> IRQ 22
mmc0: SDHCI at 0xfe5fd400 irq 22 DMA
input: HID 1241:1203 as /class/input/input3
input: USB HID v1.11 Device [HID 1241:1203] on usb-0000:00:1d.1-2.2
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 21 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1b.0 to 64
input: Logitech USB Receiver as /class/input/input4
input: USB HID v1.10 Mouse [Logitech USB Receiver] on
usb-0000:00:1d.1-2.4
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Synaptics Touchpad, model: 1, fw: 6.3, id: 0x1a0b1, caps:
0xa04793/0x300000
serio: Synaptics pass-through port at isa0060/serio1/input0
input: SynPS/2 Synaptics TouchPad as /class/input/input5
usb-storage: device scan complete
usb-storage: device scan complete
scsi 3:0:0:0: CD-ROM SONY DVD RW DRU-820A 2.0c PQ: 0
ANSI: 0
scsi 2:0:0:0: Direct-Access WDC WD12 00JB-00GVA0 0811 PQ: 0
ANSI: 0
sd 2:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 234441648 512-byte hardware sectors (120034 MB)
sd 2:0:0:0: [sdb] Test WP failed, assume Write Enabled
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sdb: sdb1 sdb2
sd 2:0:0:0: [sdb] Attached SCSI disk
hda_intel: azx_get_response timeout, switching to polling mode...
sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
sr 3:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 3:0:0:0: Attached scsi generic sg1 type 5
sd 2:0:0:0: Attached scsi generic sg2 type 0
hda_intel: azx_get_response timeout, switching to single_cmd mode...
hda_codec: No auto-config is available, default to model=ref
hda-intel: no codecs initialized
ACPI: PCI interrupt for device 0000:00:1b.0 disabled
Adding 1044184k swap on /dev/sda7. Priority:-1 extents:1
across:1044184k
EXT3 FS on sda8, internal journal
loop: module loaded
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised:
dm-devel@redhat.com
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ACPI: Battery Slot [BAT0] (battery present)
ACPI: AC Adapter [AC] (on-line)
input: Lid Switch as /class/input/input6
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input7
ACPI: Power Button (CM) [PBTN]
input: Sleep Button (CM) as /class/input/input8
ACPI: Sleep Button (CM) [SBTN]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
[drm] Initialized i915 1.6.0 20060119 on minor 0
UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
kjournald starting. Commit interval 5 seconds
EXT3-fs warning: maximal mount count reached, running e2fsck is
recommended
EXT3 FS on sdb2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
** Loaded modules:
Module Size Used by
binfmt_misc 11112 1
ipv6 236964 10
isofs 32828 2
udf 76932 0
i915 22432 1
drm 76020 2 i915
rfcomm 36280 0
l2cap 22432 5 rfcomm
bluetooth 49348 4 rfcomm,l2cap
ppdev 8676 0
parport_pc 33796 0
lp 10980 0
parport 33960 3 ppdev,parport_pc,lp
button 7920 0
ac 5188 0
battery 9988 0
acpi_cpufreq 9096 1
cpufreq_powersave 1792 0
cpufreq_userspace 4128 0
cpufreq_ondemand 8300 1
cpufreq_conservative 6888 0
cpufreq_stats 5120 0
freq_table 4512 3
acpi_cpufreq,cpufreq_ondemand,cpufreq_stats
nls_iso8859_1 4128 3
nls_cp437 5792 1
vfat 12032 1
fat 48540 1 vfat
dm_snapshot 16516 0
dm_mirror 20928 0
dm_mod 52160 2 dm_snapshot,dm_mirror
loop 16932 0
firewire_sbp2 12100 0
sg 32668 0
sr_mod 16516 1
joydev 9568 0
tsdev 7968 0
snd_hda_intel 239160 0
snd_pcm_oss 39200 0
snd_mixer_oss 15424 1 snd_pcm_oss
snd_pcm 72324 2 snd_hda_intel,snd_pcm_oss
snd_timer 21028 1 snd_pcm
sdhci 16524 0
snd 48324 5
snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
mmc_core 26116 1 sdhci
soundcore 7520 1 snd
i2c_i801 8656 0
psmouse 36016 0
usblp 13280 0
usbhid 25792 0
snd_page_alloc 9512 2 snd_hda_intel,snd_pcm
pcspkr 3104 0
hid 25248 1 usbhid
i2c_core 23552 1 i2c_i801
serio_raw 6692 0
intel_agp 23188 1
agpgart 31912 3 drm,intel_agp
evdev 9312 7
ext3 121224 3
jbd 55336 1 ext3
mbcache 8260 1 ext3
ide_cd 36416 1
cdrom 32832 2 sr_mod,ide_cd
sd_mod 27136 7
usb_storage 76608 2
generic 4836 0 [permanent]
piix 8868 0 [permanent]
ide_core 113764 4 ide_cd,usb_storage,generic,piix
firewire_ohci 16512 0
firewire_core 38816 2 firewire_sbp2,firewire_ohci
crc_itu_t 2144 1 firewire_core
b44 25516 0
mii 5280 1 b44
ata_piix 13348 4
ata_generic 7556 0
libata 115664 2 ata_piix,ata_generic
scsi_mod 136620 6
firewire_sbp2,sg,sr_mod,sd_mod,usb_storage,libata
ehci_hcd 30796 0
uhci_hcd 22960 0
usbcore 125096 6
usblp,usbhid,usb_storage,ehci_hcd,uhci_hcd
thermal 13416 0
processor 31016 2 acpi_cpufreq,thermal
fan 4836 0
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile Memory Controller
Hub [8086:2a00] (rev 0c)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile
Integrated Graphics Controller [8086:2a02] (rev 0c) (prog-if 00 [VGA])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fea00000 (64-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at efe8 [size=8]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile Integrated
Graphics Controller [8086:2a03] (rev 0c)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at feb00000 (64-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:1a.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at 6f20 [size=32]
00:1a.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 6f00 [size=32]
00:1a.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB2 EHCI #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fed1c400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD
Audio Controller [8086:284b] (rev 02)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: Memory at fe9fc000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0b, subordinate=0b, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.1 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 2 [8086:2841] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
Memory behind bridge: fe800000-fe8fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1c.3 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 4 [8086:2845] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=0d, subordinate=0e, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fe600000-fe7fffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1d.0 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 4: I/O ports at 6f80 [size=32]
00:1d.1 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 20
Region 4: I/O ports at 6f60 [size=32]
00:1d.2 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI #3 [8086:2832] (rev 02) (prog-if 00 [UHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at 6f40 [size=32]
00:1d.7 USB Controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB2 EHCI #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fed1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge
[8086:2448] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: fe500000-fe5fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation Mobile LPC Interface
Controller [8086:2815] (rev 02)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation Mobile IDE Controller
[8086:2850] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 6fa0 [size=16]
00:1f.2 IDE interface [0101]: Intel Corporation Mobile SATA IDE
Controller [8086:2828] (rev 02) (prog-if 8f [Master SecP SecO PriP
PriO])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 6eb0 [size=8]
Region 1: I/O ports at 6eb8 [size=4]
Region 2: I/O ports at 6ec0 [size=8]
Region 3: I/O ports at 6ec8 [size=4]
Region 4: I/O ports at 6ee0 [size=16]
Region 5: I/O ports at eff0 [size=16]
Capabilities: <access denied>
00:1f.3 SMBus [0c05]: Intel Corporation 82801H (ICH8 Family) SMBus
Controller [8086:283e] (rev 02)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fe9fbf00 (32-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 10c0 [size=32]
03:00.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0
100Base-TX [14e4:170c] (rev 02)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fe5fe000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
03:01.0 FireWire (IEEE 1394) [0c00]: Ricoh Co Ltd Unknown device
[1180:0832] (rev 05) (prog-if 10 [OHCI])
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fe5fd800 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
03:01.1 Generic system peripheral [0805]: Ricoh Co Ltd R5C822
SD/SDIO/MMC/MS/MSPro Host Adapter [1180:0822] (rev 22) (prog-if 01)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 22
Region 0: Memory at fe5fd400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:01.2 System peripheral [0880]: Ricoh Co Ltd Unknown device
[1180:0843] (rev 12)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at fe5fd500 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:01.3 System peripheral [0880]: Ricoh Co Ltd R5C592 Memory Stick Bus
Host Adapter [1180:0592] (rev 12)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at fe5fd600 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
03:01.4 System peripheral [0880]: Ricoh Co Ltd xD-Picture Card
Controller [1180:0852] (rev 12)
Subsystem: Dell Unknown device [1028:0228]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 4
Region 0: Memory at fe5fd700 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
0c:00.0 Network controller [0280]: Intel Corporation PRO/Wireless
3945ABG Network Connection [8086:4222] (rev 02)
Subsystem: Intel Corporation Unknown device [8086:1020]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at fe8ff000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.22-2-686 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.22-2-686 depends on:
ii initramfs-tools [linux-initr 0.90a tools for generating an
initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux
kernel mo
Versions of packages linux-image-2.6.22-2-686 recommends:
ii libc6-i686 2.6.1-1+b1 GNU C Library: Shared
libraries [i
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.22-2-686/preinst/lilo-has-ramdisk:
linux-image-2.6.22-2-686/prerm/would-invalidate-boot-loader-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/kimage-is-a-directory:
linux-image-2.6.22-2-686/preinst/elilo-initrd-2.6.22-2-686: true
linux-image-2.6.22-2-686/preinst/abort-overwrite-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/old-dir-initrd-link-2.6.22-2-686:
true
linux-image-2.6.22-2-686/prerm/removing-running-kernel-2.6.22-2-686:
true
linux-image-2.6.22-2-686/preinst/lilo-initrd-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/depmod-error-initrd-2.6.22-2-686:
false
linux-image-2.6.22-2-686/preinst/overwriting-modules-2.6.22-2-686:
true
linux-image-2.6.22-2-686/preinst/initrd-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/depmod-error-2.6.22-2-686: false
linux-image-2.6.22-2-686/preinst/already-running-this-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/old-initrd-link-2.6.22-2-686: true
linux-image-2.6.22-2-686/postinst/bootloader-test-error-2.6.22-2-686:
linux-image-2.6.22-2-686/preinst/failed-to-move-modules-2.6.22-2-686:
linux-image-2.6.22-2-686/preinst/bootloader-initrd-2.6.22-2-686: true
linux-image-2.6.22-2-686/preinst/abort-install-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/create-kimage-link-2.6.22-2-686:
true
linux-image-2.6.22-2-686/postinst/bootloader-error-2.6.22-2-686:
linux-image-2.6.22-2-686/postinst/old-system-map-link-2.6.22-2-686:
true
Reply to: