--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.32-5-686: rtl818x broken for RTL-8185 IEEE 802.11a/b/g
- From: Anton Ivanov <arivanov@sigsegv.cx>
- Date: Mon, 06 Jun 2011 17:56:05 +0100
- Message-id: <20110606165605.2993.499.reportbug@gronkle.sigsegv.cx>
Package: linux-2.6
Version: 2.6.32-34squeeze1
Severity: normal
The card is identified correctly, but never manages to associate
with an AP.
The card is a generic rtl8185 cannibalised out of a Maplin HTC
PC bundle.
Dmesg self-explanatory.
Unfortunately the web site on sourceforge seems a bit blank so
I cannot pick up a more recent driver to test build to see
if this can be fixed.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-34squeeze1) (dannf@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed May 18 07:08:50 UTC 2011
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=ddf5a907-47ff-4167-adc8-f00fd59ed1f8 ro acpi_enforce_resources=lax quiet
** Not tainted
** Kernel log:
[ 2.646116] uhci_hcd 0000:00:10.3: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 2.646134] uhci_hcd 0000:00:10.3: setting latency timer to 64
[ 2.646141] uhci_hcd 0000:00:10.3: UHCI Host Controller
[ 2.646160] uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5
[ 2.646199] uhci_hcd 0000:00:10.3: irq 21, io base 0x0000f400
[ 2.646281] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.646289] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.646295] usb usb5: Product: UHCI Host Controller
[ 2.646300] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 2.646306] usb usb5: SerialNumber: 0000:00:10.3
[ 2.646640] usb usb5: configuration #1 chosen from 1 choice
[ 2.647236] hub 5-0:1.0: USB hub found
[ 2.647276] hub 5-0:1.0: 2 ports detected
[ 2.824026] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.988236] ata2.00: ATA-7: Maxtor 6Y080M0, YAR511W0, max UDMA/100
[ 2.988245] ata2.00: 156301488 sectors, multi 16: LBA48
[ 3.004253] ata2.00: configured for UDMA/100
[ 3.004477] scsi 1:0:0:0: Direct-Access ATA Maxtor 6Y080M0 YAR5 PQ: 0 ANSI: 5
[ 3.303701] sd 1:0:0:0: [sda] 156301488 512-byte logical blocks: (80.0 GB/74.5 GiB)
[ 3.303789] sd 1:0:0:0: [sda] Write Protect is off
[ 3.303796] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 3.303832] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.304151] sda: sda1 sda2
[ 3.326469] sd 1:0:0:0: [sda] Attached SCSI disk
[ 3.599716] PM: Starting manual resume from disk
[ 3.599727] PM: Resume from partition 8:1
[ 3.599732] PM: Checking hibernation image.
[ 3.600083] PM: Error -22 checking image file
[ 3.600087] PM: Resume from disk failed.
[ 3.674961] kjournald starting. Commit interval 5 seconds
[ 3.674984] EXT3-fs: mounted filesystem with ordered data mode.
[ 5.254134] udev[309]: starting version 164
[ 5.907667] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 5.936574] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 5.936593] ACPI: Power Button [PWRB]
[ 5.936735] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 5.936752] ACPI: Sleep Button [SLPB]
[ 5.936915] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 5.936925] ACPI: Power Button [PWRF]
[ 6.076088] processor LNXCPU:00: registered as cooling_device0
[ 6.113043] input: PC Speaker as /devices/platform/pcspkr/input/input3
[ 6.197120] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 6.261327] parport_pc 00:0a: reported by Plug and Play ACPI
[ 6.261383] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
[ 6.458051] cfg80211: Using static regulatory domain info
[ 6.458058] cfg80211: Regulatory domain: US
[ 6.458064] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 6.458072] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm)
[ 6.458079] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.458087] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.458095] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.458102] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm)
[ 6.458110] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm)
[ 6.459361] cfg80211: Calling CRDA for country: US
[ 7.418256] rtl8180 0000:00:08.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 7.659638] phy0: Selected rate control algorithm 'minstrel'
[ 7.661526] phy0: hwaddr 00:e0:46:50:00:40, RTL8185vD + rtl8225z2
[ 8.002042] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 8.002065] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[ 8.002248] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 9.498139] Adding 1959888k swap on /dev/sda1. Priority:-1 extents:1 across:1959888k
[ 9.763059] EXT3 FS on sda2, internal journal
[ 9.974774] loop: module loaded
[ 10.124184] it87: Found IT8716F chip at 0x290, revision 1
[ 10.124196] it87: in3 is VCC (+5V)
[ 10.124200] it87: in7 is VCCH (+5V Stand-By)
[ 10.124284] ACPI: I/O resource it87 [0x295-0x296] conflicts with ACPI region IP__ [0x295-0x296]
[ 10.124290] ACPI: This conflict may cause random problems and system instability
[ 10.124295] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 10.125721] it87 it87.656: Detected broken BIOS defaults, disabling PWM interface
[ 10.190543] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 10.190552] All bugs added by David S. Miller <davem@redhat.com>
[ 11.046888] tun: Universal TUN/TAP device driver, 1.6
[ 11.046897] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 11.155830] ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 11.156449] e1000: eth2 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX
[ 11.157179] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 11.586395] RPC: Registered udp transport module.
[ 11.586402] RPC: Registered tcp transport module.
[ 11.586407] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 11.907910] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 11.908402] e1000: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: RX/TX
[ 11.909103] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.920095] Slow work thread pool: Starting up
[ 11.921507] Slow work thread pool: Ready
[ 11.923832] FS-Cache: Loaded
[ 12.031425] FS-Cache: Netfs 'nfs' registered for caching
[ 12.104331] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 12.471713] fuse init (API version 7.13)
[ 13.999504] svc: failed to register lockdv1 RPC service (errno 97).
[ 14.002467] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 14.020239] NFSD: starting 90-second grace period
[ 21.440013] tap0: no IPv6 routers present
[ 21.504018] eth2: no IPv6 routers present
[ 22.636012] eth0: no IPv6 routers present
[ 662.952668] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 664.112034] wlan0: direct probe to AP 00:90:4c:91:00:03 (try 1)
[ 664.312026] wlan0: direct probe to AP 00:90:4c:91:00:03 (try 2)
[ 664.512019] wlan0: direct probe to AP 00:90:4c:91:00:03 (try 3)
[ 664.712014] wlan0: direct probe to AP 00:90:4c:91:00:03 timed out
** Model information
not available
** Loaded modules:
Module Size Used by
fuse 44052 1
nfsd 193055 13
exportfs 2586 1 nfsd
nfs 206510 0
lockd 49301 2 nfsd,nfs
fscache 24422 1 nfs
nfs_acl 1695 2 nfsd,nfs
auth_rpcgss 25200 2 nfsd,nfs
sunrpc 134340 12 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
tun 8740 2
8021q 13950 0
garp 4066 1 8021q
stp 996 1 garp
it87 11487 0
hwmon_vid 1528 1 it87
loop 9729 0
snd_via82xx 15256 0
gameport 6025 1 snd_via82xx
snd_ac97_codec 79148 1 snd_via82xx
ac97_bus 710 1 snd_ac97_codec
snd_pcm_oss 28671 0
snd_mixer_oss 10461 1 snd_pcm_oss
snd_pcm 47226 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
arc4 974 2
snd_page_alloc 4977 2 snd_via82xx,snd_pcm
snd_mpu401_uart 4067 1 snd_via82xx
ecb 1405 2
snd_seq_midi 3576 0
snd_rawmidi 12513 2 snd_mpu401_uart,snd_seq_midi
rtl8180 22783 0
snd_seq_midi_event 3684 1 snd_seq_midi
snd_seq 35327 2 snd_seq_midi,snd_seq_midi_event
mac80211 122866 1 rtl8180
snd_timer 12258 2 snd_pcm,snd_seq
eeprom_93cx6 963 1 rtl8180
snd_seq_device 3673 3 snd_seq_midi,snd_rawmidi,snd_seq
snd 34387 10 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
i2c_viapro 4419 0
cfg80211 86977 2 rtl8180,mac80211
parport_pc 15799 0
psmouse 44777 0
evdev 5609 6
shpchp 21220 0
i2c_core 12751 1 i2c_viapro
parport 22554 1 parport_pc
pcspkr 1207 0
rfkill 10196 1 cfg80211
processor 26259 0
soundcore 3450 1 snd
serio_raw 2916 0
button 3598 0
pci_hotplug 18065 1 shpchp
ext3 93944 1
jbd 31965 1 ext3
mbcache 3762 1 ext3
sd_mod 25937 3
crc_t10dif 1012 1 sd_mod
ata_generic 2067 0
uhci_hcd 15989 0
pata_via 5669 0
sata_via 5576 2
via_rhine 14527 0
libata 115513 3 ata_generic,pata_via,sata_via
thermal 9206 0
ehci_hcd 28453 0
floppy 40923 0
mii 2714 1 via_rhine
scsi_mod 104613 2 sd_mod,libata
thermal_sys 9378 2 processor,thermal
usbcore 98541 3 uhci_hcd,ehci_hcd
nls_base 4541 1 usbcore
e1000 77145 0
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
auto tap0
iface tap0 inet static
address 192.168.250.254
netmask 255.255.255.0
tunctl_user uml-net
auto eth2
iface eth2 inet static
address 192.168.249.254
netmask 255.255.255.0
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100
link/ether 00:11:0a:5c:7e:56 brd ff:ff:ff:ff:ff:ff
inet 192.168.3.57/24 brd 192.168.3.255 scope global eth0
inet6 fe80::211:aff:fe5c:7e56/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
link/ether 00:1b:b9:91:7b:63 brd ff:ff:ff:ff:ff:ff
4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 100
link/ether 00:11:0a:5c:7e:57 brd ff:ff:ff:ff:ff:ff
inet 192.168.249.254/24 brd 192.168.249.255 scope global eth2
inet6 fe80::211:aff:fe5c:7e57/64 scope link
valid_lft forever preferred_lft forever
5: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:e0:46:50:00:40 brd ff:ff:ff:ff:ff:ff
6: tap0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 500
link/ether 22:24:61:af:71:6a brd ff:ff:ff:ff:ff:ff
inet 192.168.250.254/24 brd 192.168.250.255 scope global tap0
inet6 fe80::2024:61ff:feaf:716a/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 8756 104 0 0 0 0 0 0 8756 104 0 0 0 0 0 0
eth0: 344161 1805 0 0 0 0 0 0 234296 1032 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth2: 4832 36 0 0 0 0 0 0 4860 42 0 0 0 0 0 0
wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
tap0: 0 0 0 0 0 0 0 0 230 3 0 3 0 0 0 0
*** Protocol statistics:
Ip:
1811 total packets received
0 forwarded
0 incoming packets discarded
1809 incoming packets delivered
1143 requests sent out
Icmp:
0 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
0 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
Tcp:
5 active connections openings
4 passive connection openings
0 failed connection attempts
0 connection resets received
2 connections established
1563 segments received
982 segments send out
0 segments retransmited
0 bad segments received.
0 resets sent
Udp:
170 packets received
0 packets to unknown port received.
0 packet receive errors
161 packets sent
UdpLite:
TcpExt:
3 TCP sockets finished time wait in fast timer
9 delayed acks sent
6 packets directly queued to recvmsg prequeue.
419 packet headers predicted
63 acknowledgments not containing data payload received
730 predicted acknowledgments
IpExt:
InNoRoutes: 2
InBcastPkts: 85
InOctets: 325811
OutOctets: 230648
InBcastOctets: 16350
*** Device features:
eth0: 0x10b89
eth1: 0x0
eth2: 0x10b89
lo: 0x13865
tap0: 0x0
wlan0: 0x2000
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:0314]
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at e8000000 (32-bit, prefetchable) [size=128M]
Capabilities: [80] AGP version 3.5
Status: RQ=8 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: agpgart-via
00:00.1 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:1314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:2314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. PT890 Host Bridge [1106:3208]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.4 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:4314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:00.7 Host bridge [0600]: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host Bridge [1106:7314]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: fb000000-fcffffff
Prefetchable memory behind bridge: f4000000-f7ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR+ <PERR+
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [70] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:08.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185] (rev 20)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller [10ec:8185]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at f000 [size=256]
Region 1: Memory at fdfff000 (32-bit, non-prefetchable) [size=512]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: rtl8180
00:09.0 Ethernet controller [0200]: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) [8086:1010] (rev 01)
Subsystem: Compaq Computer Corporation NC7170 Gigabit Server Adapter [0e11:00db]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 252 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fdfc0000 (64-bit, non-prefetchable) [size=128K]
Region 2: Memory at fdf40000 (64-bit, non-prefetchable) [size=256K]
Region 4: I/O ports at ff00 [size=64]
[virtual] Expansion ROM at 3c000000 [disabled] [size=256K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: e1000
00:09.1 Ethernet controller [0200]: Intel Corporation 82546EB Gigabit Ethernet Controller (Copper) [8086:1010] (rev 01)
Subsystem: Compaq Computer Corporation NC7170 Gigabit Server Adapter [0e11:00db]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 252 (63750ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 18
Region 0: Memory at fdfa0000 (64-bit, non-prefetchable) [size=128K]
Region 4: I/O ports at fe00 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [e4] PCI-X non-bridge device
Command: DPERE- ERO+ RBC=512 OST=1
Status: Dev=00:00.1 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=1 DMCRS=16 RSCEM- 266MHz- 533MHz-
Capabilities: [f0] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Kernel driver in use: e1000
00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin B routed to IRQ 20
Region 0: I/O ports at fd00 [size=8]
Region 1: I/O ports at fc00 [size=4]
Region 2: I/O ports at fb00 [size=8]
Region 3: I/O ports at fa00 [size=4]
Region 4: I/O ports at f900 [size=16]
Region 5: I/O ports at f200 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_via
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at f800 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_via
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at f700 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at f600 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at f500 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at f400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 21
Region 0: Memory at fdffe000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227]
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60)
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 22
Region 0: I/O ports at ee00 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA 82xx Audio
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 78)
Subsystem: Elitegroup Computer Systems Device [1019:0102]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (750ns min, 2000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at ea00 [size=256]
Region 1: Memory at fdffd000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: via-rhine
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. CN700/P4M800 Pro/P4M800 CE/VN800 [S3 UniChrome Pro] [1106:3344] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Elitegroup Computer Systems Device [1019:aa51]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f4000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at fc000000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [70] AGP version 3.0
Status: RQ=256 Iso- ArqSz=0 Cal=7 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA+ AGP- GART64- 64bit- FW- Rate=<none>
** USB devices:
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0.1
APT prefers stable-updates
APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-34squeeze1 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
pn firmware-linux-free <none> (no description available)
ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information excluded
--- End Message ---