Bug#760215: linux-image-3.14-2-kirkwood: Not enough space in MTD RootFS1 (need 9768399 but is actually 9437184)
Package: src:linux
Version: 3.14.15-2
Severity: grave
Justification: renders package unusable
Dear Maintainer,
* What led up to the situation?
Upgrading the package linux-image-kirkwood that depends on this one.
* What exactly did you do (or not do) that was effective (or
ineffective)?
dpkg-reconfigure the package reproduces the error.
* What was the outcome of this action?
The following error messages:
Processing triggers for flash-kernel (3.21) ...
flash-kernel: installing version 3.14-2-kirkwood
Not enough space in MTD RootFS1 (need 9768399 but is actually 9437184).
dpkg: error processing package flash-kernel (--configure):
el subproceso instalado el script post-installation devolvió el código de salida de error 1
Se encontraron errores al procesar:
flash-kernel
* What outcome did you expect instead?
Proper installation of the package.
-- Package-specific info:
This kernel could not be booted because it can't get installed.
** Model information
Hardware : QNAP TS-41x
Revision : 0000
** PCI devices:
00:00.0 Host bridge [0600]: Marvell Technology Group Ltd. 88F6281 [Kirkwood] ARM SoC [11ab:6281] (rev 02)
Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at <ignored> (64-bit, prefetchable)
Capabilities: <access denied>
00:01.0 SCSI storage controller [0100]: Marvell Technology Group Ltd. 88SX7042 PCI-e 4-port SATA-II [11ab:7042] (rev 02)
Subsystem: Marvell Technology Group Ltd. Device [11ab:11ab]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 9
Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=1M]
Region 2: I/O ports at 1000 [size=256]
Capabilities: <access denied>
Kernel driver in use: sata_mv
** USB devices:
Bus 001 Device 002: ID 05e3:0608 Genesys Logic, Inc. USB-2.0 4-Port HUB
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 051d:0002 American Power Conversion Uninterruptible Power Supply
-- System Information:
Debian Release: jessie/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: armel (armv5tel)
Kernel: Linux 3.9-1-kirkwood
Locale: LANG=es_ES.UTF-8, LC_CTYPE=es_ES.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.14-2-kirkwood depends on:
ii debconf [debconf-2.0] 1.5.53
ii initramfs-tools [linux-initramfs-tool] 0.115
ii kmod 17-2
ii linux-base 3.5
ii module-init-tools 17-2
Versions of packages linux-image-3.14-2-kirkwood recommends:
ii firmware-linux-free 3.3
ii uboot-mkimage 2012.04.01-2
Versions of packages linux-image-3.14-2-kirkwood suggests:
pn debian-kernel-handbook <none>
pn fdutils <none>
pn linux-doc-3.14 <none>
Versions of packages linux-image-3.14-2-kirkwood is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.14-2-kirkwood/postinst/depmod-error-initrd-3.14-2-kirkwood: false
linux-image-3.14-2-kirkwood/postinst/mips-initrd-3.14-2-kirkwood:
linux-image-3.14-2-kirkwood/prerm/removing-running-kernel-3.14-2-kirkwood: true
Reply to: