Bug#810726: linux-image-4.3.0-1-amd64: Kernel 4.3 breaks Hauppauge HD-PVR recording
Javier and Mauro, this is in regards to Debian bug #810726, which I
filed last week. I also informed Hans about it at that time.
Using git bisect, I finally identified the attached commit as the
offending one. Sure enough, after reverting that change, my hdpvr
behaves reliably with the 4.3.3 kernel. Further testing has revealed
that I can achieve the same result with the standard, Debian kernel by
blacklisting the ir_kbd_i2c module.
It seems something in the IR initialization is causing the hdpvr to
become unreliable. This is even when the IR support is not used nor
wanted. Additionally, blacklisting the lirc_zilog module is not
sufficient to work around the problem, nor is keeping it but using the
tx_only=1 parameter.
David
On Mon, Jan 11, 2016 at 10:27:23AM -0600, David Engel wrote:
> Package: src:linux
> Version: 4.3.3-5
> Severity: normal
>
> Dear Maintainer,
>
> My Hauppauge HD-PVR USB recorder started locking up recently. By that
> I mean it would start sending data when directed, but would stop any
> where from a few to several minutes later and would require a power
> cycle to get back. This behavior was consistent and would never run
> for longer than about 20 minutes before locking up. When the lockups
> occured, there were no kernel log messages.
>
> I eventually determined the problem was with the 4.3 Linux kernel,
> specifically, the linux-image-4.3.0-1-amd64 package. The coincidence
> wasn't apparent at first because I didn't use the HD-PVR for some days
> after updating to the 4.3 kernel. After rebooting with the 4.2
> kernel, the HD-PVR has performed flawlessly like it had for the
> previous, several months.
>
> Looking at Linus' kernel source, it appears the hdpvr driver has not
> had any changes in nearly a year. I suspect the regression lies
> elsewhere in the general, USB code.
>
> *** Reporter, please consider answering these questions, where appropriate ***
>
> * What led up to the situation?
> * What exactly did you do (or not do) that was effective (or
> ineffective)?
> * What was the outcome of this action?
> * What outcome did you expect instead?
>
> *** End of the template - remove these template lines ***
>
>
> -- Package-specific info:
> ** Kernel log: boot messages should be attached
>
> ** Model information
> sys_vendor: To Be Filled By O.E.M.
> product_name: To Be Filled By O.E.M.
> product_version: To Be Filled By O.E.M.
> chassis_vendor: To Be Filled By O.E.M.
> chassis_version: To Be Filled By O.E.M.
> bios_vendor: American Megatrends Inc.
> bios_version: P1.60
> board_vendor: ASRock
> board_name: Z77 Pro4
> board_version:
>
> ** PCI devices:
> 00:00.0 Host bridge [0600]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller [8086:0150] (rev 09)
> Subsystem: ASRock Incorporation Motherboard [1849:0150]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
> Latency: 0
> Capabilities: <access denied>
> Kernel driver in use: ivb_uncore
>
> 00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port [8086:0151] (rev 09) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 24
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
> Memory behind bridge: f5000000-f70fffff
> Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
> Subsystem: ASRock Incorporation Motherboard [1849:1e31]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 26
> Region 0: Memory at f7e00000 (64-bit, non-prefetchable) [size=64K]
> Capabilities: <access denied>
> Kernel driver in use: xhci_hcd
>
> 00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
> Subsystem: ASRock Incorporation Motherboard [1849:1e3a]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 29
> Region 0: Memory at f7e1a000 (64-bit, non-prefetchable) [size=16]
> Capabilities: <access denied>
> Kernel driver in use: mei_me
>
> 00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
> Subsystem: ASRock Incorporation Motherboard [1849:1e2d]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 16
> Region 0: Memory at f7e18000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: <access denied>
> Kernel driver in use: ehci-pci
>
> 00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
> Subsystem: ASRock Incorporation Device [1849:8892]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 31
> Region 0: Memory at f7e10000 (64-bit, non-prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: snd_hda_intel
>
> 00:1c.0 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 [8086:1e10] (rev c4) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 16
> Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
> Memory behind bridge: f7400000-f7bfffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1c.4 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev c4) (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 11
> Bus: primary=00, secondary=03, subordinate=04, sec-latency=0
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
>
> 00:1c.5 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 6 [8086:1e1a] (rev c4) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin B routed to IRQ 17
> Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
> I/O behind bridge: 0000e000-0000efff
> Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1c.6 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 7 [8086:1e1c] (rev c4) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin C routed to IRQ 18
> Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
> Memory behind bridge: f7d00000-f7dfffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1c.7 PCI bridge [0604]: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 8 [8086:1e1e] (rev c4) (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin D routed to IRQ 19
> Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
> I/O behind bridge: 0000d000-0000dfff
> Memory behind bridge: f7c00000-f7cfffff
> Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
> Kernel driver in use: pcieport
>
> 00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
> Subsystem: ASRock Incorporation Motherboard [1849:1e26]
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin A routed to IRQ 23
> Region 0: Memory at f7e17000 (32-bit, non-prefetchable) [size=1K]
> Capabilities: <access denied>
> Kernel driver in use: ehci-pci
>
> 00:1f.0 ISA bridge [0601]: Intel Corporation Z77 Express Chipset LPC Controller [8086:1e44] (rev 04)
> Subsystem: ASRock Incorporation Motherboard [1849:1e44]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Capabilities: <access denied>
> Kernel driver in use: lpc_ich
>
> 00:1f.2 SATA controller [0106]: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e02] (rev 04) (prog-if 01 [AHCI 1.0])
> Subsystem: ASRock Incorporation Motherboard [1849:1e02]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
> Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0
> Interrupt: pin B routed to IRQ 27
> Region 0: I/O ports at f070 [size=8]
> Region 1: I/O ports at f060 [size=4]
> Region 2: I/O ports at f050 [size=8]
> Region 3: I/O ports at f040 [size=4]
> Region 4: I/O ports at f020 [size=32]
> Region 5: Memory at f7e16000 (32-bit, non-prefetchable) [size=2K]
> Capabilities: <access denied>
> Kernel driver in use: ahci
>
> 00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
> Subsystem: ASRock Incorporation Motherboard [1849:1e22]
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Interrupt: pin C routed to IRQ 18
> Region 0: Memory at f7e15000 (64-bit, non-prefetchable) [size=256]
> Region 4: I/O ports at f000 [size=32]
>
> 01:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV44 [GeForce 6200 TurboCache] [10de:0161] (rev a1) (prog-if 00 [VGA controller])
> Subsystem: eVga.com. Corp. Device [3842:c223]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 11
> Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=16M]
> Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
> Region 3: Memory at f5000000 (64-bit, non-prefetchable) [size=16M]
> Expansion ROM at f7000000 [disabled] [size=128K]
> Capabilities: <access denied>
>
> 02:00.0 Multimedia controller [0480]: Philips Semiconductors SAA7164 [1131:7164] (rev 81)
> Subsystem: Hauppauge computer works Inc. WinTV HVR-2250 [0070:8851]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 30
> Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
> Region 2: Memory at f7400000 (64-bit, non-prefetchable) [size=4M]
> Capabilities: <access denied>
> Kernel driver in use: saa7164
>
> 03:00.0 PCI bridge [0604]: ASMedia Technology Inc. ASM1083/1085 PCIe to PCI Bridge [1b21:1080] (rev 03) (prog-if 01 [Subtractive decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 11
> Bus: primary=03, secondary=04, subordinate=04, sec-latency=64
> Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: <access denied>
>
> 05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
> Subsystem: ASRock Incorporation Motherboard (one of many) [1849:8168]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 25
> Region 0: I/O ports at e000 [size=256]
> Region 2: Memory at f0004000 (64-bit, prefetchable) [size=4K]
> Region 4: Memory at f0000000 (64-bit, prefetchable) [size=16K]
> Capabilities: <access denied>
> Kernel driver in use: r8169
>
> 06:00.0 FireWire (IEEE 1394) [0c00]: JMicron Technology Corp. IEEE 1394 Host Controller [197b:2380] (prog-if 10 [OHCI])
> Subsystem: JMicron Technology Corp. IEEE 1394 Host Controller [197b:2380]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort+ <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 18
> Region 0: Memory at f7d03000 (32-bit, non-prefetchable) [size=2K]
> Region 1: Memory at f7d02000 (32-bit, non-prefetchable) [size=128]
> Region 4: Memory at f7d01000 (32-bit, non-prefetchable) [size=128]
> Region 5: Memory at f7d00000 (32-bit, non-prefetchable) [size=128]
> Capabilities: <access denied>
> Kernel driver in use: firewire_ohci
>
> 07:00.0 SATA controller [0106]: ASMedia Technology Inc. ASM1062 Serial ATA Controller [1b21:0612] (rev 01) (prog-if 01 [AHCI 1.0])
> Subsystem: ASRock Incorporation Motherboard [1849:0612]
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> Latency: 0, Cache Line Size: 32 bytes
> Interrupt: pin A routed to IRQ 28
> Region 0: I/O ports at d050 [size=8]
> Region 1: I/O ports at d040 [size=4]
> Region 2: I/O ports at d030 [size=8]
> Region 3: I/O ports at d020 [size=4]
> Region 4: I/O ports at d000 [size=32]
> Region 5: Memory at f7c00000 (32-bit, non-prefetchable) [size=512]
> Capabilities: <access denied>
> Kernel driver in use: ahci
>
>
> ** USB devices:
> Bus 002 Device 009: ID 2040:4902 Hauppauge HD PVR
> Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
> Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>
>
> -- System Information:
> Debian Release: stretch/sid
> APT prefers testing
> APT policy: (900, 'testing'), (100, 'unstable'), (1, 'experimental')
> Architecture: amd64 (x86_64)
>
> Kernel: Linux 4.2.0-1-amd64 (SMP w/4 CPU cores)
> Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
> Shell: /bin/sh linked to /bin/dash
> Init: systemd (via /run/systemd/system)
>
> Versions of packages linux-image-4.3.0-1-amd64 depends on:
> ii debconf [debconf-2.0] 1.5.58
> ii initramfs-tools [linux-initramfs-tool] 0.120
> ii kmod 21-1
> ii linux-base 4.0
>
> Versions of packages linux-image-4.3.0-1-amd64 recommends:
> pn firmware-linux-free <none>
> ii irqbalance 1.0.9-1
>
> Versions of packages linux-image-4.3.0-1-amd64 suggests:
> pn debian-kernel-handbook <none>
> ii grub-pc 2.02~beta2-33
> pn linux-doc-4.3 <none>
>
> Versions of packages linux-image-4.3.0-1-amd64 is related to:
> pn firmware-atheros <none>
> pn firmware-bnx2 <none>
> pn firmware-bnx2x <none>
> pn firmware-brcm80211 <none>
> pn firmware-intelwimax <none>
> pn firmware-ipw2x00 <none>
> pn firmware-ivtv <none>
> pn firmware-iwlwifi <none>
> pn firmware-libertas <none>
> pn firmware-linux <none>
> pn firmware-linux-nonfree <none>
> pn firmware-myricom <none>
> pn firmware-netxen <none>
> pn firmware-qlogic <none>
> pn firmware-ralink <none>
> ii firmware-realtek 20151207-1
> pn xen-hypervisor <none>
>
> -- debconf information:
> linux-image-4.3.0-1-amd64/prerm/removing-running-kernel-4.3.0-1-amd64: true
> linux-image-4.3.0-1-amd64/postinst/mips-initrd-4.3.0-1-amd64:
> linux-image-4.3.0-1-amd64/postinst/depmod-error-initrd-4.3.0-1-amd64: false
--
David Engel
david@istwok.net
commit ed8d1cf07cb16dacc5414cb46a5a48517c9b98f9
Author: Javier Martinez Canillas <javier@osg.samsung.com>
Date: Thu Jul 30 13:18:29 2015 -0300
[media] Export I2C module alias information in missing drivers
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
diff --git a/drivers/media/i2c/ir-kbd-i2c.c b/drivers/media/i2c/ir-kbd-i2c.c
index 175a761..728d2cc 100644
--- a/drivers/media/i2c/ir-kbd-i2c.c
+++ b/drivers/media/i2c/ir-kbd-i2c.c
@@ -478,6 +478,7 @@ static const struct i2c_device_id ir_kbd_id[] = {
{ "ir_rx_z8f0811_hdpvr", 0 },
{ }
};
+MODULE_DEVICE_TABLE(i2c, ir_kbd_id);
static struct i2c_driver ir_kbd_driver = {
.driver = {
diff --git a/drivers/media/i2c/s5k6a3.c b/drivers/media/i2c/s5k6a3.c
index bc389d5..b1b1574 100644
--- a/drivers/media/i2c/s5k6a3.c
+++ b/drivers/media/i2c/s5k6a3.c
@@ -363,6 +363,7 @@ static int s5k6a3_remove(struct i2c_client *client)
static const struct i2c_device_id s5k6a3_ids[] = {
{ }
};
+MODULE_DEVICE_TABLE(i2c, s5k6a3_ids);
#ifdef CONFIG_OF
static const struct of_device_id s5k6a3_of_match[] = {
Reply to: