Bug#906052: linux-image-4.17.0-1-armmp: Compex WLE900VX (ath10k) doesn't probe
Package: src:linux
Version: 4.17.8-1
Severity: normal
Dear Maintainer,
The Compex pci express wifi module fails to probe apparently because it isn't
waking up. I can't see anything wrong here, and the module used to work with
older (vendor) kernels.
Any clues what is going on?
Yours sincerely
Josua Mayer
-- Package-specific info:
** Version:
Linux version 4.17.0-1-armmp (debian-kernel@lists.debian.org) (gcc version 7.3.0 (Debian 7.3.0-26)) #1 SMP Debian 4.17.8-1 (2018-07-20)
** Command line:
console=ttyS0,115200 log_level=7
** Not tainted
** Kernel log:
[ 4.416771] xhci-hcd f10f8000.usb3: irq 49, io mem 0xf10f8000
[ 4.422722] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 4.17
[ 4.431024] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.438269] usb usb4: Product: xHCI Host Controller
[ 4.443161] usb usb4: Manufacturer: Linux 4.17.0-1-armmp xhci-hcd
[ 4.449273] usb usb4: SerialNumber: f10f8000.usb3
[ 4.454319] hub 4-0:1.0: USB hub found
[ 4.458105] hub 4-0:1.0: 1 port detected
[ 4.462249] xhci-hcd f10f8000.usb3: xHCI Host Controller
[ 4.467591] xhci-hcd f10f8000.usb3: new USB bus registered, assigned bus number 5
[ 4.475109] xhci-hcd f10f8000.usb3: Host supports USB 3.0 SuperSpeed
[ 4.481601] usb usb5: We don't know the algorithms for LPM for this host, disabling LPM.
[ 4.489774] usb usb5: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 4.17
[ 4.498067] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.505312] usb usb5: Product: xHCI Host Controller
[ 4.507447] libphy: mv88e6xxx SMI: probed
[ 4.510205] usb usb5: Manufacturer: Linux 4.17.0-1-armmp xhci-hcd
[ 4.510210] usb usb5: SerialNumber: f10f8000.usb3
[ 4.525199] mvebu-pcie soc:pcie: PCI host bridge to bus 0000:00
[ 4.531163] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 4.537424] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 4.538185] hub 5-0:1.0: USB hub found
[ 4.543750] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 4.547530] hub 5-0:1.0: 1 port detected
[ 4.554399] ata1.00: ATA-10: 32GB SATA Flash Drive, SFPS925A, max UDMA/133
[ 4.565229] ata1.00: 62533296 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.573566] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 4.579734] pci 0000:00:02.0: [11ab:6828] type 01 class 0x060400
[ 4.579934] pci 0000:00:03.0: [11ab:6828] type 01 class 0x060400
[ 4.581309] PCI: bus0: Fast back to back transfers disabled
[ 4.586922] pci 0000:00:02.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.594958] pci 0000:00:03.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 4.603149] ata1.00: configured for UDMA/133
[ 4.607484] pci 0000:01:00.0: [168c:003c] type 00 class 0x028000
[ 4.607516] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[ 4.607542] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
[ 4.607632] pci 0000:01:00.0: supports D1 D2
[ 4.607759] scsi 0:0:0:0: Direct-Access ATA 32GB SATA Flash 925A PQ: 0 ANSI: 5
[ 4.607790] pci 0000:00:02.0: ASPM: current common clock configuration is broken, reconfiguring
[ 4.624813] sd 0:0:0:0: [sda] 62533296 512-byte logical blocks: (32.0 GB/29.8 GiB)
[ 4.632799] sd 0:0:0:0: [sda] Write Protect is off
[ 4.637615] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.637642] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.647734] sda: sda1 sda2 sda3 < sda5 >
[ 4.652559] sd 0:0:0:0: [sda] Attached SCSI removable disk
[ 4.658927] PCI: bus1: Fast back to back transfers enabled
[ 4.664475] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 4.665827] PCI: bus2: Fast back to back transfers enabled
[ 4.671365] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 4.671391] pci 0000:00:02.0: BAR 8: assigned [mem 0xe0000000-0xe02fffff]
[ 4.678247] pci 0000:01:00.0: BAR 0: assigned [mem 0xe0000000-0xe01fffff 64bit]
[ 4.685609] pci 0000:01:00.0: BAR 0: error updating (0xe0000004 != 0xffffffff)
[ 4.692890] pci 0000:01:00.0: BAR 0: error updating (high 0x000000 != 0xffffffff)
[ 4.700416] pci 0000:01:00.0: BAR 6: assigned [mem 0xe0200000-0xe020ffff pref]
[ 4.706967] random: fast init done
[ 4.707688] pci 0000:00:02.0: PCI bridge to [bus 01]
[ 4.716066] pci 0000:00:02.0: bridge window [mem 0xe0000000-0xe02fffff]
[ 4.722883] pci 0000:00:03.0: PCI bridge to [bus 02]
[ 4.730477] pcieport 0000:00:02.0: enabling device (0140 -> 0142)
[ 5.339193] Marvell 88E1540 mv88e6xxx-0:00: attached PHY driver [Marvell 88E1540] (mii_bus:phy_addr=mv88e6xxx-0:00, irq=64)
[ 5.431158] Marvell 88E1540 mv88e6xxx-0:01: attached PHY driver [Marvell 88E1540] (mii_bus:phy_addr=mv88e6xxx-0:01, irq=65)
[ 5.521407] Marvell 88E1540 mv88e6xxx-0:02: attached PHY driver [Marvell 88E1540] (mii_bus:phy_addr=mv88e6xxx-0:02, irq=66)
[ 5.613400] Marvell 88E1540 mv88e6xxx-0:03: attached PHY driver [Marvell 88E1540] (mii_bus:phy_addr=mv88e6xxx-0:03, irq=67)
[ 5.705399] Marvell 88E1540 mv88e6xxx-0:04: attached PHY driver [Marvell 88E1540] (mii_bus:phy_addr=mv88e6xxx-0:04, irq=68)
[ 5.727761] Generic PHY fixed-0:01: attached PHY driver [Generic PHY] (mii_bus:phy_addr=fixed-0:01, irq=POLL)
[ 5.738466] DSA: tree 0 setup
[ 5.824674] PM: Image not found (code -22)
[ 5.932270] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 6.128816] systemd[1]: systemd 239 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 6.150428] systemd[1]: Detected architecture arm.
[ 6.172937] systemd[1]: Set hostname to <clearfog>.
[ 6.378459] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.385356] systemd[1]: Listening on Journal Audit Socket.
[ 6.404795] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.411699] systemd[1]: Listening on udev Control Socket.
[ 6.432818] random: systemd: uninitialized urandom read (16 bytes read)
[ 6.439629] systemd[1]: Listening on udev Kernel Socket.
[ 6.460880] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 6.485013] systemd[1]: Listening on Journal Socket.
[ 6.508021] systemd[1]: Starting udev Coldplug all Devices...
[ 6.531097] systemd[1]: Starting Create list of required static device nodes for the current kernel...
[ 6.721307] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 7.109289] systemd-journald[215]: Received request to flush runtime journal from PID 1
[ 7.396739] orion_wdt: Initial timeout 171 sec
[ 7.460748] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 7.696587] marvell-cesa f1090000.crypto: CESA device successfully registered
[ 7.818741] ath10k_pci 0000:01:00.0: of_irq_parse_pci: failed with rc=134
[ 7.844739] ath10k_pci 0000:01:00.0: Refused to change power state, currently in D3
[ 7.882641] ath10k_pci 0000:01:00.0: failed to wake up device : -110
[ 7.891012] ath10k_pci: probe of 0000:01:00.0 failed with error -110
[ 8.095389] Adding 998396k swap on /dev/sda5. Priority:-2 extents:1 across:998396k SSFS
[ 8.234962] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[ 8.245236] EXT4-fs (sda1): mounted filesystem without journal. Opts: (null)
[ 8.485309] mvneta f1070000.ethernet eth0: PHY [f1072004.mdio-mii:00] driver [Marvell 88E1510]
[ 8.494243] mvneta f1070000.ethernet eth0: configuring for phy/rgmii-id link mode
[ 8.503770] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.673445] mvneta f1070000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.681504] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 313.920370] random: crng init done
[ 313.925220] random: 7 urandom warning(s) missed due to ratelimiting
** Model information
Hardware : Marvell Armada 380/385 (Device Tree)
Revision : 0000
Device Tree model: SolidRun Clearfog A1
** Loaded modules:
ath10k_pci
ath10k_core
ath
mac80211
cfg80211
rfkill
marvell_cesa
des_generic
sg
orion_wdt
spi_orion
evdev
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
fscrypto
ecb
sd_mod
mv88e6xxx
dsa_core
bridge
stp
llc
devlink
gpio_pca953x
ehci_orion
ehci_hcd
xhci_plat_hcd
sdhci_pxav3
sdhci_pltfm
xhci_hcd
marvell
sdhci
ahci_mvebu
libahci_platform
libahci
libata
scsi_mod
mvmdio
usbcore
mvneta
phylink
i2c_mv64xxx
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet dhcp
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 532
link/ether d2:63:b4:fb:4f:8a brd ff:ff:ff:ff:ff:ff
inet 192.168.1.138/24 brd 192.168.1.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fd9e:cdca:47d1:0:d063:b4ff:fefb:4f8a/64 scope global dynamic mngtmpaddr
valid_lft forever preferred_lft forever
inet6 fe80::d063:b4ff:fefb:4f8a/64 scope link
valid_lft forever preferred_lft forever
3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 532
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
4: eth2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 532
link/ether d2:63:b4:fb:4f:8c brd ff:ff:ff:ff:ff:ff
5: lan5@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
6: lan4@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
7: lan3@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
8: lan2@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
9: lan1@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
10: lan6@eth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc noop state DOWN group default qlen 1000
link/ether d2:63:b4:fb:4f:8b brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lan2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lan4: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lan1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lan5: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth2: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lan6: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
eth0: 522101 529 0 0 0 0 0 0 173501 373 0 0 0 0 0 0
lan3: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
** PCI devices:
00:02.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [11ab:6828] (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e0000000-e02fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:03.0 PCI bridge [0604]: Marvell Technology Group Ltd. Device [11ab:6828] (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
01:00.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x 802.11ac Wireless Network Adapter [168c:003c] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel modules: ath10k_pci
** USB devices:
Bus 005 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: buster/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: armhf (armv7l)
Kernel: Linux 4.17.0-1-armmp (SMP w/2 CPU cores)
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8), LANGUAGE=en_GB:en (charmap=UTF-8)
Shell: /bin/sh linked to /usr/bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.17.0-1-armmp depends on:
ii initramfs-tools [linux-initramfs-tool] 0.132
ii kmod 25-1
ii linux-base 4.5
Versions of packages linux-image-4.17.0-1-armmp recommends:
pn apparmor <none>
pn firmware-linux-free <none>
pn irqbalance <none>
Versions of packages linux-image-4.17.0-1-armmp suggests:
pn debian-kernel-handbook <none>
pn linux-doc-4.17 <none>
Versions of packages linux-image-4.17.0-1-armmp is related to:
pn firmware-amd-graphics <none>
ii firmware-atheros 20180518-1
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
pn firmware-misc-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
Reply to: