LG LPNCII PCMCIA (Rtl-8139)- cannot even ping
Hi!
I've got HP OmniBook 5700CTX (P166MMX) with 2.4.20 kernel
and I try to use 10/100Mbps Realport PC Card LG LPNCII-10/100
(Cardbus). This card is Realtek RTL-8139 chip based.
I use yenta_socket and 8139too module (8139cp does not work).
The problem is that I can load the modules, ifconfig the card,
but I can't even ping my not-mobile computer (there is Intel
EtherExpress PRO/10+ ISA - I use eepro module and everything
looks OK). I'm sure that cable and both cards are fine, because
if I run on the laptop Win98 I can ping each other.
I have tried several things but nothing works :-(.
Have you got any idea??
May be these infos will help:
first of all laptop IP: 192.168.0.12
non-mobile computer IP: 192.168.0.1
I know there are lot of stuff below, but I don't know where
to search for the hint even :-(
*** "route -n" on both computers ***
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0
127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo
***
*** "iptables --list" on both computers ***
Chain INPUT (policy ACCEPT)
target prot opt source destination
Chain FORWARD (policy ACCEPT)
target prot opt source destination
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
***
*** "ifconfig" on desktop computer ***
eth0 Link encap:Ethernet HWaddr 00:AA:00:C8:3B:68
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:3 Base address:0x200
/* I cut off lo interface */
***
*** "ifconfig" on laptop BEFORE "ping 192.168.0.1" ***
eth0 Link encap:Ethernet HWaddr 00:40:F4:5D:B5:FB
inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x1000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
***
*** "ifconfig" on laptop AFTER "ping 192.168.0.1" ***
eth0 Link encap:Ethernet HWaddr 00:40:F4:5D:B5:FB
inet addr:192.168.0.12 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:10 Base address:0x1000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:7 errors:0 dropped:0 overruns:0 frame:0
TX packets:7 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:784 (784.0 b) TX bytes:784 (784.0 b)
/* I have no idea why it goes to the loopback ?!? */
***
*** "lsmod" ***
Module Size Used by Not tainted
8139too 15272 1
mii 2240 0 [8139too]
ds 6568 2
yenta_socket 9632 2
pcmcia_core 38112 0 [ds yenta_socket]
ide-scsi 8048 0
***
*** "lspci" ***
00:00.0 Host bridge: OPTi Inc. 82C557 [Viper-M] (rev 14)
00:01.0 ISA bridge: OPTi Inc. 82C558 [Viper-M ISA+IDE] (rev 02)
00:02.0 VGA compatible controller: Chips and Technologies F65554 (rev c2)
00:03.0 CardBus bridge: Texas Instruments PCI1131 (rev 01)
00:03.1 CardBus bridge: Texas Instruments PCI1131 (rev 01)
00:14.0 IDE interface: OPTi Inc. 82C621 [Viper-M/N+] (rev 12)
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
***
*** "cat /var/log/messages" ***
Aug 6 19:24:55 darkstar kernel: eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
Aug 6 19:25:37 darkstar kernel: NETDEV WATCHDOG: eth0: transmit timed out
Aug 6 19:25:37 darkstar kernel: eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
***
*** "cat /var/log/syslog" ***
Aug 6 19:24:09 darkstar kernel: Yenta IRQ list 0898, PCI irq10
Aug 6 19:24:09 darkstar kernel: Socket status: 30000020
Aug 6 19:24:09 darkstar kernel: Yenta IRQ list 0898, PCI irq10
Aug 6 19:24:09 darkstar kernel: Socket status: 30000006
Aug 6 19:24:09 darkstar kernel: PCI: Enabling device 01:00.0 (0000 -> 0003)
***
Any help will be apreciated
Thanks in advance
rosa
---
rosa (at) poznan.telbank.pl
Reply to: