AMD K6 2 - 350. New install. Some doubts...
Hi all.
I bought an AMD K6 250 and it seems to come with a lot of hardware
within it:
a sound board, modem, video, ...
but the software is for Windows and with few documentation...
I have some doubts:
1) My old modem worked only with isapnp and then setserial.
How to automate on boot setserial settings given by isapnp?
2) The sound board seems to be PCI Sound PRO? Is there support in
Linux for this?
3) The video board is a Sis.
The following is my pci:
[05:23:14]paulo@phantasy:~$cat /proc/pci
PCI devices found:
Bus 0, device 0, function 0:
Host bridge: Silicon Integrated Systems Unknown device (rev 2).
Vendor id=1039. Device id=530.
Medium devsel. Master Capable. Latency=32.
Non-prefetchable 32 bit memory at 0xe8000000 [0xe8000000].
Bus 0, device 0, function 1:
IDE interface: Silicon Integrated Systems 85C5513 (rev 208).
Fast devsel. Master Capable. Latency=128.
I/O at 0x1f0 [0x1f1].
I/O at 0x3f4 [0x3f5].
I/O at 0x170 [0x171].
I/O at 0x374 [0x375].
I/O at 0xffa0 [0xffa1].
Bus 0, device 1, function 0:
ISA bridge: Silicon Integrated Systems 85C503 (rev 177).
Medium devsel. Master Capable. No bursts.
Bus 0, device 1, function 1:
Unknown class: Silicon Integrated Systems ACPI (rev 0).
Medium devsel.
Bus 0, device 2, function 0:
PCI bridge: Silicon Integrated Systems 5591/5592 AGP (rev 0).
Fast devsel. Master Capable. No bursts. Min Gnt=4.
Bus 0, device 9, function 0:
VGA compatible controller: Trident TG 9660 / Cyber9385 (rev 211).
Medium devsel. Fast back-to-back capable.
Non-prefetchable 32 bit memory at 0xefc00000 [0xefc00000].
Non-prefetchable 32 bit memory at 0xefbf0000 [0xefbf0000].
Bus 0, device 10, function 0:
Ethernet controller: Realtek 8029 (rev 0).
Medium devsel. IRQ 11.
I/O at 0xdc00 [0xdc01].
Bus 0, device 12, function 0:
Multimedia audio controller: Unknown vendor Unknown device (rev 16).
Vendor id=13f6. Device id=100.
Medium devsel. IRQ 10. Master Capable. Latency=32. Min
Gnt=2.Max Lat=24.
I/O at 0xde00 [0xde01].
Bus 1, device 0, function 0:
VGA compatible controller: Silicon Integrated Systems Unknown device
(rev 162).
Vendor id=1039. Device id=6306.
Medium devsel. Master Capable. Latency=32. Min Gnt=2.
Prefetchable 32 bit memory at 0xff000000 [0xff000008].
Non-prefetchable 32 bit memory at 0xe76f0000 [0xe76f0000].
I/O at 0xcc00 [0xcc01].
[05:23:16]paulo@phantasy:~$
[05:24:36]paulo@phantasy:~$cat /proc/ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03e8-03ef : serial(set)
03f6-03f6 : ide0
03f8-03ff : serial(set)
dc00-dc1f : eth0
ffa0-ffa7 : ide0
ffa8-ffaf : ide1
[05:24:40]paulo@phantasy:~$
[05:24:40]paulo@phantasy:~$cat /proc/interrupts
CPU0
0: 3434258 XT-PIC timer
1: 19526 XT-PIC keyboard
2: 0 XT-PIC cascade
4: 127848 XT-PIC serial
5: 2911225 XT-PIC serial
11: 278778 XT-PIC eth0
13: 0 XT-PIC fpu
14: 365962 XT-PIC ide0
15: 448 XT-PIC ide1
NMI: 0
[05:24:54]paulo@phantasy:~$
My old sound board is an Sound Blaster 16 that I took off.
[05:25:05]paulo@phantasy:~$cat /proc/sound
OSS/Free:3.8s2++-971130
Load type: Driver compiled into kernel
Kernel: Linux phantasy 2.2.9 #1 Sat May 15 15:12:24 EST 1999 i586
Config options: 0
Installed drivers:
Type 1: OPL-2/OPL-3 FM
Type 26: MPU-401 (UART)
Type 2: Sound Blaster
Type 29: Sound Blaster PnP
Type 7: SB MPU-401
Card config:
(Sound Blaster at 0x220 irq 5 drq 1,5)
(SB MPU-401 at 0x330 irq 1 drq 0)
(OPL-2/OPL-3 FM at 0x388 drq 0)
Audio devices:
Synth devices:
Midi devices:
Timers:
0: System clock
Mixers:
[05:25:48]paulo@phantasy:~$
Thanks for any help, Paulo Henrique
Reply to: