Re: more info on dhcpcd problem
Heh, thanks for the reality check. I wil;l give the dynip and forwarding a
shot -- can't hurt :) as for the cables and card, cable is known good, and
one of the network cards is known good. And, I thought of the firewall rules
in the wee hours of the morning -- they seemed fine, but setting all to
default to allow, it still didn't go. :(
I am hoping you are right with the dynip thingy -- but one thing that
worries me -- it might be my motherboard won't handle two PCI devices
wanting to be bus masters -- and that doesn't even consider my video card
(stealth 3d 3000 -- anyone know one way or the other? :)
Thanks again for your help! :)
On Wed, Sep 01, 1999 at 08:49:29AM -0400, Constantine Karbaliotis wrote:
> 1. make sure that you have enabled dynamic ip addressing and forwarding in your
> network script before you call dhclient/dhcpcd (since they are not enabled by
> default):
>
> echo "1" > /proc/sys/net/ipv4/ip_dynaddr
> echo "1" > /pro/sys/net/ipv4/ip_forward
>
> 2. check your cables and card. make sure that they are not the problem. sounds
> stupid, i know, but more than once i have wasted time thinking I had done something
> wrong when it was a bad cable or card.
> 3. if you have set up a firewall , make sure that you are not blocking yourself from
> getting out; maybe disable it for at least one startup, if these other things don't
> work.
>
> that having been said, there is something flaky about the dhcp/dhclient setup on
> debian; i cannot understand why it works and then, when the cable co that I connect
> to has changed my ip or other features, i cannot connect; the purpose of dhcp is to
> be dynamic, is it not?
>
> Seth R Arnold wrote:
>
> > Constantine, thanks for your help, but I am back again.. :)
> >
> > I removed dhcpcd and replaced it with dhcp-client-beta and dhcp-beta (or
> > whichever package contains the docs for dhcp-client-beta) from my slink
> > release 2 CDs.
> >
> > Still no go.
> >
> > I get the same "Operation not permitted" error message. It just looks a
> > little different now. :(
> >
> > Anyone? please? :)
> >
> > On Tue, Aug 31, 1999 at 03:09:07PM -0400, Constantine Karbaliotis wrote:
> > > Seth, I have never been able to get dhcpcd to work. I installed dhclient
> > > and the only success I've had, was with that. Perhaps you could try
> > > removing dhcpcd and installing the package called dhcp-client-beta from
> > > the Debian installation CD's. Mind you, I am still having trouble even
> > > though I created a setup which successfully connected, and consistently
> > > for some time; now it doesn't, and nothing has changed in my setup. I
> > > suspect that changes to my cable company's dhcp servers have been taking
> > > place, which makes it very hard to diagnose problems.
> > >
> > > Seth R Arnold wrote:
> > >
> > > > Boy, I hate this... :)
> > > >
> > > > I think I mistyped my first submission to this mailing list. Here it is
> > > > again, verbatim, save for fixing the errors I know I had in it.
> > > >
> > > > Hey gang, I desperatly need your help. I don't think my slink's dhcpcd
> > > > is properly doing the dhcpdiscover.
> > > >
> > > > Specs: kernel 2.0.36, both custom and debian-default two 3c905b network
> > > > cards (plan on ipmasq :) 3c59x.c driver from both debian-default and
> > > > from donald becker's page (Currently loading as a module.. btw, where to
> > > > specify module options?) Pentium II 266 oc to 300, on early motherboard
> > > >
> > > > I sure wish I could cut'n'paste the error messages. I ran
> > > > /usr/sbin/dhcpcd -d eth0
> > > >
> > > > and after a few seconds of waiting, I get a message similar to: sendto
> > > > (init): Operation not permitted
> > > >
> > > > running that command as root, and having it fail thusly is annoying. :)
> > > >
> > > > I have tried to run the dhcpcd with ifconfig eth0 up and ifconfig eth0
> > > > down. I am pretty sure it is eth0 because ifconfig shows that interface
> > > > reciving thousands of packets -- but sending NONE.
> > > >
> > > > After running "/usr/sbin/dhcpcd eth0", it does not show up in ps aux,
> > > > and "killall dhcpcd" gives "no processes killed".
> > > >
> > > > Should I load network driver into kernel, rather than as module? (keep
> > > > in mind, TWO network cards.. :)
> > > >
> > > > Should eth0 be UP or DOWN before running dhcpcd? Should I ifconfig eth0
> > > > to a bogus IP before running dhcpcd? how about netmask?
> > > >
> > > > Please guys, I am very much sad at theloss of my internet... ;) (loss in
> > > > the sense that when I was at home my windows machine had a modem...
> > > > here, my linux machine has no modem, and no network access just yet...
> > > > :( it hasn't worked in this configuration before... new network cards,
> > > > new debian, etc.. :)
> > > >
> > > > Thanks.
> > > >
> > > > On Tue, Aug 31, 1999 at 02:22:38AM -0700, Seth R Arnold wrote:
> > > > > Oh yes -- an addition to my last email. Where I said the error message
> > > > > looks like "xxx (init): cannot something.."
> > > > >
> > > > > the "xxx" should read: "sendto"
> > > > >
> > > > > I get the same error message when I try to ping places too. :)
> > > >
> > > > -- Seth Arnold | http://www.willamette.edu/~sarnold/ Hate spam? See
> > > > http://maps.vix.com/rbl/ for help Hi! I'm a .signature virus! Copy me
> > > > into your ~/.signature to help me spread!
> > > >
> > > > -- Unsubscribe? mail -s unsubscribe
> > > > debian-user-request@lists.debian.org < /dev/null
> > >
> > >
> > > -- Unsubscribe? mail -s unsubscribe debian-user-request@lists.debian.org
> > > < /dev/null
> >
> > --
> > Seth Arnold | http://www.willamette.edu/~sarnold/
> > Hate spam? See http://maps.vix.com/rbl/ for help
> > Hi! I'm a .signature virus! Copy me into
> > your ~/.signature to help me spread!
> >
> > --
> > Unsubscribe? mail -s unsubscribe debian-user-request@lists.debian.org < /dev/null
--
Seth Arnold | http://www.willamette.edu/~sarnold/
Hate spam? See http://maps.vix.com/rbl/ for help
Hi! I'm a .signature virus! Copy me into
your ~/.signature to help me spread!
Reply to: